Ultrapure Water: Benefits and Uses

Ultrapure Water: Benefits and Uses

Ultra pure water (also known as UPW) — is water that has been treated to the highest levels of purity for all contaminant types. In simple words it is water that’s free from any impurities, which makes it widely used in power engineering, science-intensive industries, instrumentation and mechanical engineering, production of high-purity substances.

Ultrapure water: how does it work?

Many people might begin to answer that last question by listing all of the things that are dissolved in ultrapure water. The reality, though, is that ultrapure water has fewer impurities than even distilled water. Distilled water leaves behind many minerals through distillation processes that concentrate certain contaminants into a smaller volume of liquid – but not only are these minerals typically benign ( some exceptions), they’re also intact and able to be reintroduced into a human body. Ultrapure water, on the other hand, is prepared by stripping every last impurity from the liquid.

This process is done using ion-exchange columns – you can think of them as batteries for ions (charged atoms or molecules). In an ion-exchange column, negatively charged resin beads are mixed with positively charged contaminants, and those two charges make it possible for water to “soak” up some of those contaminants depending on how strong the charge is on both ends of the chemical equation. Most impurities that end up in ultrapure water will have more negative charges than positive ones attached to them, which means they will soak up more positively-charged contaminants over time. Filtration processes are then used to remove any excess resin beads and other solids.

There are a few different types of ion exchange columns, depending on the desired low level of impurities in ultrapure water. The most common method is countercurrent solvent extraction with an elutriation or buffer solution – it’s a little bit like repeatedly going over a spot on your carpet with a vacuum cleaner, only instead of dirt you’re pulling out dissolved contaminants from the liquid. This system can be used for months without needing to worry about replacing the resin beads inside of the column.

What Industries Require Ultrapure Water?

Power Generation

Super-critical boilers rely on ultra-pure water for power generation. The water must be purified of H+ and OH- ions if it is to sustain the correct levels of water conductivity. Power plants generally rely on membrane filtration or ion exchange to achieve conductivity levels of 10 uS/cm, the same levels required in the semiconductor industry.

Semiconductor Manufacturing

The semiconductor industry relies on both pure and ultrapure water to manufacture circuit boards and other sensitive electronic components. Many water-soluble minerals leave a residue that can impact performance, so demineralised water is frequently used. This is produced through deionisation in a resin exchange or electro-deionisation plant.

Pharmaceutical Manufacturing

The water purification requirements of the pharmaceutical industry vary according to the different ways manufacturers use water. When used for injections, water must be filtered in a way that keeps tight control over bacteria levels. Water must be completely sterile, so double pass reverse osmosis and distillation is often used. Osmotic pressure alone can provide the saline water required to clean machinery, while reverse osmosis is ideal for reducing bioburdens. By limiting the water-borne compounds microorganisms rely on to proliferate, high purity water can be produced less expensively. Particle removal supports bacteria control and reduces the risk of microbial contamination. Once it takes hold, contamination can be difficult to treat without chemicals that themselves affect the water quality. Water used in inhalants and dilutants must also be sterile, as must the steam used to sterilise products and machinery.

Food & Beverage Industries

The food and beverage industry is held to ever-increasing hygiene requirements, particularly in terms of water quality. Water used for producing intermediate and final products must be demineralised and filtered to pure levels. Some beverages require a specific mineral composition for their water – including many beers. To achieve this, brewers first remove all compounds from their water by deionisation or distillation, then re-add the desired minerals in the required quantities.

Agriculture

Water used for irrigation doesn’t normally need to be ultra-pure but must have the right pH level. Salinity and minerals are hazardous to sensitive crops, and residual nitrogen can expose them to algal growth, so irrigation water must be tested frequently. Where brackish water is required, industrial reverse osmosis system is a good way to maintain the right quality standards without removing essential salts.

Mining

The mining industry must recycle feed water and wastewater so no contaminant is discharged into the water table. While ultra-pure standards aren’t required for this, coping with dense sludge and acidic mine drainage is demanding on a filtration system.

What Can Ultrapure Water Be Used For?

As mentioned earlier, one of the key uses for ultrapure water is within semiconductor manufacturing processes. Ultrapure water is needed at almost every step of the process, from initial cleansing to cooling and rinsing in between. There is so much demand for ultrapure water in semiconductor manufacturing that some companies have been experimenting with creating “clean rooms” filled with ultrapure air – but this isn’t always a perfect solution. From getting rid of the dust particles to keeping dissolved impurities from ruining water, sometimes there’s simply no substitute for pure water.

One area where ultrapure water has seen a surge of interest lately is nanotechnology research. Some components used specifically in biological studies require ultrapure water to function properly – which means everything from using pump devices that can handle high osmotic pressure to making sure that all surfaces are clean while using complicated analytical tools.

As for other uses, ultrapure water is preferred by pharmaceutical companies in some cases. It’s also useful in some types of chemical synthesis – although depending on how demanding the process needs to be, distilled water may be good enough for certain applications. The main thing to keep in mind is that there are different grades of purity when it comes to water – so even if something isn’t strictly necessary, it doesn’t hurt to have high concentration levels of dissolved substances.

Of course, not every application will benefit from ultrapure water. Drinking it wouldn’t be particularly healthy – and besides, purified drinking water is readily available at most grocery stores and other public locations. If you’re trying to create ultrapure water, it’s important to know that many contaminants can slip through the filters used in purification systems – and sometimes this just isn’t worth the time and money required to produce something so pure.

Ultrapure Water: What Can It Do?

There are several benefits associated with ultrapure water, such as:

  • Removes dissolved gases from chemicals and pharmaceuticals
  • Lowers the vapour pressure in pharmaceutical manufacturing facilities to prevent corrosion
  • Keeps metals shiny by reducing oxidation and rusting (this prevents employees from having to sandblast surfaces before finishing them)
  • Prevents microbial growth found in or well water, helping companies avoid the risk of bacterial infections
  • Ensures that batteries and semiconductors function properly – this also extends their usable life and helps them perform better
  • Prevents product contamination and gives products a longer shelf life because there are no bacteria or chemicals left behind after processing
  • Helps companies comply with government regulations associated with the use of ultrapure water, such as those mentioned above.  

What you also need to know about ultrapure water?

No, unless you will drink it too much. One glass of ultra pure water won’t do anything to your health. But if you will drink it often, you would lose many important electrolytes.

No, as they have a different process of production. Ultrapure water has a longer production algorithm that requires a lot of technology (reverse osmosis, activated carbon, ion exchanger).

Find Out More

At Wychwood Water, we design and supply the equipment necessary to treat water to ultrapure standards. For a Free quote or to speak with an engineer about your requirements, please contact us!